Teac TV Remote Not Working: Reasons and DIY Fixes
If the Teac TV remote is not working, you may be confused about whether to replace the remote or not. In most situations, the remote stops working due to weak batteries, blockage by any objects, etc. Since these problems are frequent in all Smart TV remotes, you can resolve such problems and make the remote work normally. So, you don’t need to buy a replacement remote for Teac TV.
In this article, you will learn the causes and troubleshooting methods to fix the Teac TV remote not working issue.
Why is My Teac TV Remote Not Working
If you encounter problems using the Teac TV remote, it may be due to the following reasons.
| SCENARIO | REASONS |
|---|---|
| 1 | If the Teac TV remote has weak or drained batteries |
| 2 | The remote’s IR emitter is defective due to an accidental fall |
| 3 | Due to a speck of dirt, the keys may stuck inside the remote |
| 4 | Because of signal blockage, the IR signals won’t be sent to the TV |
| 5 | If the remote gets affected by liquid spillage, it will make the remote faulty |
| 6 | If the Teac TV encounters a technical error, the remote may not work |
How to Fix Teac TV Remote Not Working
If the Teac TV remote is not working, you can fix it using the troubleshooting methods below.
Replace the Batteries
The remote will not work properly if the batteries are low or drained completely. So, it is a must to check and replace the old batteries with new ones. Gently open the remote compartment and remove the batteries from the Teac TV remote. Then, insert the new batteries based on the positive and negative terminals and close the battery compartment. Now, point the remote towards the TV and check whether the remote works well without any issues.
Note: Replacing the old batteries is the best workaround that is effective in fixing the Digihome TV remote not working issue.
Test the IR Emitter
If the Teac TV remote is not working even with new batteries, the issue may be with the remote’s IR emitter. So, if you feel your remote sensor might be blocked or undergoing any issues, open the Camera app on your smartphone. Point the remote sensor in front of your smartphone’s camera and press the buttons. If you can see a flashing light, there is no issue with the Teac TV remote. If no flashlight is visible, it means that the remote’s sensor has become faulty, and you need to buy a new remote.
Note: If you think a replacement remote is costly, use the IR blaster remote app as a virtual remote for Teac TV.
Clean the Teac TV Remote
The keys on your remote will not work if dirt or gunk is settled between the buttons. To avoid this problem, it is recommended to clean your Teac TV remote at least once a week. You can use 99% isopropyl alcohol solution, microfiber cloth, toothpicks, cotton swabs, or tissue paper to clean your remote. Later, insert the batteries and check if the remote is working without any issues.
Release Stuck Buttons
Sometimes, dirt may penetrate into the remote button’s gap and make your button much tighter. In rare cases, the remote keys may even be jammed, preventing it from working properly. To fix that, press all the buttons on the remote multiple times. If you can disassemble the remote, do it and clean the dust particles thoroughly using a microfiber cloth. After that, check whether the remote works without any issues.
Clear the Obstructions
Normally, infrared remotes need a clear path to send signals to the receiver. If there is an object between the TV and the remote, the TV won’t respond to remote commands because of obstructions. Therefore, you should relocate showpieces or soundbars if they were placed in front of the TV sensor. So, clean the receiver of the Teac TV if you see debris on it. The optimum range for operating the remote is less than 30 feet.
Power Cycle Teac TV
If there is any technical issue with the TV, the Teac TV will fail to respond to the remote commands. So, you must restart your Teac TV to fix the issue. Restarting the TV will refresh all the applications installed and will make the TV run smoothly without any issues. Remember, it will not delete the saved data or information stored on your TV.
[1] Turn off your TV and unplug the TV cord from the power socket.
[2] Wait for one to two minutes and keep your TV idle.
[3] Then, plug the TV cord back into the power socket.
[4] Now, turn on your TV and see if the remote is working fine or not.
Power Cycle Teac TV Remote
Like power cycling the TV, you need to power cycle your Teac TV remote. This method helps to clear the residual power left inside the remote. Remove the batteries from the remote and keep them aside. Hit the Power button on the remote and hold it for 20 seconds. Later, insert the batteries back into the remote and test whether it works without issues.
Note: You can also fix the Telefunken TV remote not working issue by power cycling the TV and the remote.
Contact Teac Support
If the remote issue is not yet fixed, even after trying all the above workarounds, you can visit the Teac Customer Support website. Then, enter the information about the product and contact information, and tap Ask a Question. Within 24 hours, Teac TV customer support will address the issue and get back to you with a relevant solution.
Use the Remote App
As an alternative, you can use remote apps to operate your TV. Since there is no official Teac TV remote app, you shall download the third-party universal remote apps on your smartphone to control your TV. To use the remote app, you should connect the TV and phone to the same WiFi network. Otherwise, your smartphone should be capable of emitting infrared signals to the TV.
Buy a Universal Remote
If the remote is found defective, buy a new Teac TV replacement remote right away instead of trying the troubleshooting methods. If you feel that the original remote costs high, buy a universal remote, which is cheaper than the original remote. However, you should know the Teac TV remote codes to program a universal remote to the TV and use it.
FAQ
Teac TV won’t respond to remote commands if sunlight has direct contact with the TV sensor. To prevent UV rays from interfering with the remote’s IR signals, you can close the doors and windows.
Yes, you can. Press the physical power button on the TV panel to turn on the Teac TV without a remote.
Unplug the TV cord from the power source and press the Power button for 10-15 seconds. After that, plug the TV cord back into the source and press the Power button to turn on the TV.
