Spectrum TV Remote Not Working: Possible Causes & DIY Fixes
There are possibilities for you to face Spectrum TV remote not working for varied reasons. The common reason behind the issue is the weak or poor batteries or physical damage in the remote. It may sometimes occur when there are obstructions that reside between the remote and the TV. Since there is no official Spectrum remote app available to control the TV, it becomes quintessential to resolve the issue. No matter what causes the Spectrum remote to not work, there are troubleshooting techniques that help resolve the issue.
Why is Spectrum TV Remote Not Working
The common reasons for your Spectrum TV remote not working issue are listed down.
|1||Your remote batteries might be weak or drained completely.|
|2||Any physical damage on your signal or antenna transmitter.|
|3||The data on the remote is not set up correctly or interfering with the device’s general performance.|
|4||Remote pairing is not done correctly.|
|5||Damage in the remote or an issue with the Spectrum cable box.|
How to Fix Spectrum TV Remote Not Working
If your Spectrum TV remote fails to work, follow the fixes mentioned below to resolve the issue.
Check the Remote Batteries
The main reason for the remote not working is poor or dead batteries. So, check the batteries on your remote and replace the old ones with fresh batteries. Also, ensure to place the batteries correctly in the battery compartment.
- Remove the batteries from the Spectrum TV remote
- Insert the new batteries based on the positive and negative terminals, as mentioned.
- Close the battery compartment and turn on the Spectrum TV.
- Now, point the remote towards the Spectrum TV and check whether the remote works well without any issues.
If any obstacles interfere with the path between the remote and the TV, then probably the remote won’t work properly. So, ensure to clear the obstacles placed before the TV and remote.
Remove Dirt or Debris
Another reason for the Spectrum TV not working is because of too much dirt stuck on the remote keys. So, make sure to clean the LED IR blaster on the remote, as there is a chance the LED IR blaster might get covered with dust particles.
Use a microfiber cloth or a paper towel to clean the outer part of the device. You can also use the cotton swab, tooth picker, or earbuds to clean the dirt in and around the buttons.
Enable TV Control
If you’re Spectrum TV is not set up to control the TV, your TV will not respond to the button you press on the remote. So, enable the remote control of your TV using the Spectrum remote by following the below steps.
 First, press the Menu button on your Spectrum remote.
 Using the directional keys, go to the Settings & Support option.
 Press the Ok button to open it.
 Navigate to the Remote Control option using the arrow keys.
 Next, select the Connect Remote to TV option. Following that, select the Connect to TV option on the next screen.
 Here, you will see the list of TV brands. Click the View All button to see the entire list.
 Choose your TV Set and press the Ok button.
 Follow the on-screen instruction and control your TV with your Spectrum remote.
Power Cycle Spectrum TV
Performing the soft reset might help fix many problems, especially when the remote is not working.
 Turn off your Spectrum TV and unplug the power cable from the socket.
 Remove the batteries from the Spectrum TV remote and wait for a few minutes.
 Then, press and hold the Power button on the remote for a couple of minutes.
 Plug the cable back into the socket and insert the batteries back into the remote.
 Now, see if the remote is working properly or not.
Unpair and Re-pair Spectrum Remote
When your remote doesn’t pair with your TV or set-top box properly, then the remote might not work properly. Hence, you should unpair and reprogram the Spectrum remote to the TV. If this fix doesn’t resolve the Spectrum remote not working, you shall try out the other fixes given below.
Switch Between Cable and TV
Usually, controls are automatically set to the cable instead of the TV, which makes sense if the TV is turned off. So, when you press the Volume or Channel button, the signal goes to the cable module. Follow the below steps to switch between cable and TV.
 On your remote, press and hold the CBL button (top right corner).
 Then, press and hold the Ok/SEL button on the remote for a few seconds and release it.
 Press the Volume down button, and the CBL button will start flashing.
 That’s it. Now, when you press the buttons on the remote, the signal will send to the TV instead of the cable.
 If you need to go back to the cable, press the Volume Up button.
Reset Spectrum Remote to Factory Default
Sometimes, if you’ve programmed your remote incorrectly, then there is a chance of getting the Spectrum remote not working issue. Before resetting the Spectrum remote, you need to remember that it will delete everything.
 First, on your remote, press and hold the TV button.
 While pressing the TV button, press the OK button and release both of them.
 You will see the TV, DVD, and AUX button will start to flash, and the TV button will remain lit up.
 Next, press and hold the Delete button for 3 seconds, and now the TV button will blink and turn off.
 Now, your Spectrum remote will be reset to factory settings.
 Next, you need to repair it with the RF1IR converter.
- Remove the RF2IR converter from the Set Top Box and press and hold the Find button
- While holding the Find button, insert the RF2IR converter back into the box
- Release the Find button, and this will delete your old pairing code
- Now, bring the remote close to the set-top box and press any buttons to pair it with the RF2IR controller
- Upon pairing, press the Find key on the RF2IR controller, and it will make a sound and will start to operate.
Contact Spectrum Help Center
If the Spectrum remote not working issue is not fixed even after resetting the TV remote, contact Spectrum Help. In addition, you shall even reach out to the Spectrum Customer Service Number and explain the issue you’re facing, and they will help you to find the necessary solution easily.
Buy a Universal Remote
Alternatively, you shall buy the Spectrum remote or Universal Remote controller, which is available on Amazon at an affordable cost. Also, make sure to buy the AAA batteries additionally and insert them into the remote before use.
If there is any issue with an internet connection or the receiver is not getting the signal from the main service, then you encounter the Spectrum remote guide button not working issue.
To fix it, press Menu on your remote → choose the Guide option → OK/Select. If the issue continues, reboot your receiver. For that, unplug the power cord from the power source and plug it back in after 30 seconds.
It may not work when the batteries are weak, the TV and cable receiver Set-Top-Box isn’t turned on, or due to the obstacles.
Yes. You can fix it by restarting the remote. For that, simply press and hold the TV/Control Center button and Volume Down button simultaneously for 5 seconds until you see the light turn off and turn on.