If your Changhong TV remote is not working, you may be thinking of ordering a new replacement remote. You can actually make the remote work if it stops working due to worn-out batteries, stuck buttons, infrared signal interference, etc. Hence, you can try these useful workarounds to bring the Changhong TV remote to a working condition. In case you find that the remote’s IR emitter is defective, you can buy a new universal remote or use the remote app to control the TV.
Why is the Changhong TV Remote Not Working
The Changhong TV remote is not responding to the commands, it is due to the following reasons.
| SCENARIO | CAUSES |
|---|---|
| 1 | Due to weak batteries, you will get slow responsiveness while using the remote |
| 2 | If there is an issue with the IR emitter, the TV won’t receive commands from the remote |
| 3 | Technical problems with the Changhong TV can be the reason if the remote doesn’t work |
| 4 | The remote may become defective due to physical damage or affected by wear and tear |
| 5 | Excessive dirt may accumulate on the buttons due to uncleanness so the remote won’t work |
How to Troubleshoot Changhong TV Remote Not Working
The following troubleshooting methods will make your Changhong TV remote work like a newer one.
Replace the Remote Batteries
When it comes to the remote, batteries play a vital role. If the batteries are very low or drained completely, the remote will not work and you will be experiencing issues like slow responsiveness. The only solution is to replace the batteries with newer ones. Before replacing the batteries, you should clean the battery terminals to make sure that no dust inside the battery compartment.
Test IR Emitter on the Remote
If there is any damage to the IR emitter, then the remote will stop working. Using the smartphone camera app, you can check if the IR emitter has an issue or not. Open the Camera app on your mobile phone. Point the remote’s IR emitter head towards the camera. Press the remote buttons to see whether you can see the blinking light. If the light blinks, there is no issue with the remote. If you can’t see the blinking light, it means the IR emitter is damaged and you need to buy a new replacement remote.
Note: If the IR emitter is the problem, you can use the IR blaster remote app to control the TV from an Android device.
Power Cycling the Remote
Power cycling is another best way to fix remote problems. This method helps to clear the residual power left inside the remote. Remove the batteries from the remote and keep them aside. Press the Power button on the remote and hold it for 20 seconds. Later, insert the batteries back into the remote and test if it is working without issues.
Release the Stuck Buttons
Since remotes are made up of plastic and rubber material, there is a high chance that dirt or gunk is jammed in between the buttons. As a result, the dirt may go inside the button, causing the buttons to get stuck inside. To avoid this problem, clean your Changhong TV remote at least once a week. You can use 99% isopropyl alcohol solution, microfiber cloth, toothpicks, cotton swabs, or tissue paper, to clean your remote.
Clear the Obstructions
Importantly, the infrared remote needs a direct line of sight to function properly. At times, objects like soundbars, speakers, or any furniture items may block the remote signals. So, you should not place any objects between the TV sensor and the Changhong TV remote. Also, use the remote in a closer range of fewer than 30 feet.
Power Cycling the TV
If you think that the issue may be with your Changhong TV, you should power cycle the TV immediately.
[1] Turn off your Changhong TV and unplug the power cable from the socket.
[2] Wait for a few minutes and keep your TV idle.
[3] Plug the cable back into the socket and see if the remote is working properly or not.
Factory Reset Changhong TV
Resetting is the one-last solution that would help to bring back your Changhong TV to its initial settings. Eventually, it would fix the Changhong TV remote not working issue. Using the Changhong TV remote app, you can easily reset your Changhong TV without a remote controller.
[1] Install the Changhong TV remote app on your smartphone.
[2] Launch the app and press the Menu button.
[3] From the TV menu, select Option to view it.
[3] Select the Reset option and you will see the warning message on the screen.
[4] Click Yes or OK to confirm the factory reset.
Contact Changhong TV Support
If the Changhong TV remote is still not working after trying these methods, you can contact Changhong TV Customer Care. Explain the issue clearly and they will assist you with a good solution. If required, you can contact their official toll-free number 0800 1958 000 to speak to a customer support agent or compose a mail at [email protected] to raise a complaint.
Buy a Universal Remote
Suppose the Changhong TV remote is damaged or faulty, it is better to buy a new Changhong TV replacement remote or universal remote. These remotes are available on Amazon at a very low cost. Most universal remotes require remote programming to use, so you have to refer to the user manual to program it.
FAQ
Yes, you shall use the Changhong TV remote app or physical buttons on the TV panel to control your smart TV without using a remote.
Yes. Locate the power button of your Changhong TV and press it to turn on your TV.
To reset the remote, remove the batteries from the remote and hold the power button for 20 seconds. Then, insert the batteries back into the remote to complete the reset process.
Using the remote app, go to Menu on Changhong TV > Select Option > Click Reset > Tap Yes/OK > Reset will be initiated.
.
